JN0-364유효한공부문제 & JN0-364완벽한덤프

Wiki Article

2026 KoreaDumps 최신 JN0-364 PDF 버전 시험 문제집과 JN0-364 시험 문제 및 답변 무료 공유: https://drive.google.com/open?id=19OW6SSL5VpUGzYj3VcPwsF9jf-lzAYJB

KoreaDumps의Juniper인증 JN0-364덤프는 고객님의 IT인증자격증을 취득하는 소원을들어줍니다. IT업계에 금방 종사한 분은 자격증을 많이 취득하여 자신만의 가치를 업그레이드할수 있습니다. KoreaDumps의Juniper인증 JN0-364덤프는 실제 시험문제에 대비하여 연구제작된 퍼펙트한 시험전 공부자료로서 시험이 더는 어렵지 않게 느끼도록 편하게 도와드립니다.

KoreaDumps의 Juniper인증 JN0-364시험덤프는 고객님의 IT자격증을 취득하는 꿈을 실현시켜 드리는 시험패스의 지름길입니다. Juniper인증 JN0-364덤프에는 실제시험문제의 거의 모든 문제를 적중하고 습니다. KoreaDumps의 Juniper인증 JN0-364덤프가 있으면 시험패스가 한결 간편해집니다.

>> JN0-364유효한 공부문제 <<

Juniper JN0-364완벽한 덤프 - JN0-364시험문제모음

만약 아직도Juniper JN0-364인증시험 위하여 많은 시간과 정력을 소모하며 열심히 공부하고 있습니까? 아직도 어덯게하면Juniper JN0-364인증시험을 빠르게 취득할 수 있는 방법을 못찿고 계십니까? 지금KoreaDumps에서Juniper JN0-364인증시험을 안전하게 넘을 수 있도록 대책을 내드리겠습니다. 아주 신기한 효과가 있을 것입니다.

최신 JNCIS-SP JN0-364 무료샘플문제 (Q52-Q57):

질문 # 52
Referring to the exhibit. You are asked to configure OSPF between routers R1 and R2 using IPv6 addresses. Which two tasks will accomplish your objective? (Choose two.)

정답：A,B

설명：
To configure OSPFv3 (the version of OSPF that supports IPv6), you would use the set protocols ospf3 command with the appropriate area and interface. OSPFv3 requires a 32-bit router ID just like OSPFv2, which is typically an IPv4 address. OSPF does not use a 128-bit router ID, so answer D is incorrect.


질문 # 53
In an OSPF network, what is a purpose of a designated router?

정답：B

설명：
On multi-access network segments, such asEthernet, OSPF could potentially face a scalability issue. If every router on a segment formed a full adjacency with every other router, the number of adjacencies would follow the formula $n(n-1)/2$. In a segment with 10 routers, this would result in 45 adjacencies, each generating redundant flooding of Link-State Advertisements (LSAs) and excessive Hello traffic.
To solve this, OSPF elects aDesignated Router (DR)and aBackup Designated Router (BDR). According to Juniper Networks documentation, the primary purpose of the DR is to act as a central point of contact for the segment, therebyreducing OSPF traffic (Option C).
Instead of every router syncing with every other router, they all form aFull adjacencyonly with the DR and BDR. When a router (a DR-Other) has an update, it sends it to the multicast address224.0.0.6(All DR Routers). The DR then acknowledges the update and floods it to all other routers on the segment using the multicast address224.0.0.5(All OSPF Routers). This "hub-and-spoke" signaling model within the local segment significantly minimizes the bandwidth consumed by protocol overhead and reduces the CPU load on the participating routers.
It is important to note that the DR's scope is limited to the local segment; it does not "assign IDs" (Option A) nor does it flood routes to the "entire domain" (Option D), as that is the responsibility of individual routers within their respective areas.


질문 # 54
Which IS-IS packet type will establish and maintain neighbor relationships?

정답：C

설명：
In theIS-IS (Intermediate System to Intermediate System)protocol, communication between routers is performed usingProtocol Data Units (PDUs). To discover neighbors and maintain adjacencies, IS-IS relies on theHello PDU (IIH - IS-IS Hello).
According to Juniper Networks technical documentation, when IS-IS is enabled on an interface, the router begins transmitting Hello PDUs to a multi-destination address (multicast). These PDUs contain essential information such as the router'sSystem ID, its configuredArea Addresses, and itsLevel capability(Level 1, Level 2, or both). For two routers to become neighbors, they must exchange these Hello PDUs and agree on specific parameters, such as the MTU of the link and the hello/hold timers.
Once an adjacency is established, the Hello PDU serves as a "keepalive" mechanism. If a router stops receiving Hello PDUs from a neighbor for a duration exceeding theHolding Time, it assumes the neighbor is down and flushes the associated Link-State PDUs (LSPs) from its database.
To clarify the other options:
* Link-State PDU (Option A):These are used to distribute actual topology and reachability information, not to form adjacencies.
* Partial Sequence Number PDU (Option C):PSNPs are used on point-to-point links to acknowledge the receipt of LSPs or to request missing LSPs.
* Update PDU (Option D):This is not a standard IS-IS term; in IS-IS, updates are handled via the flooding of LSPs.


질문 # 55
Which two statements are correct about TLVs in IS-IS? (Choose two.)

정답：A,B

설명：
In the IS-IS protocol,TLVs (Type, Length, Value)are the fundamental building blocks used to carry information withinLink-State PDUs (LSPs). Unlike some other protocols that have a fixed, rigid packet format, IS-IS was designed from the ground up to be modular and extensible. This extensibility is achieved through the use of TLVs, which allow the protocol to carry different types of data without requiring changes to the core protocol state machine.
According to Juniper Networks technical documentation,TLVs allow flexible encoding of routing information (Option C). Each TLV specifies the "Type" of information it carries (such as neighbor information or IP reachability), the "Length" of that information, and the "Value" (the actual data). This architecture is what allowed IS-IS to easily support IPv6 by simply adding new TLVs (like TLV 236 for IPv6 reachability) without redesigning the protocol. It also supports Traffic Engineering (TE) extensions used in MPLS environments by adding TLVs that describe link bandwidth and administrative groups.
Furthermore, a singleLSP can contain multiple TLVs (Option D). When a Juniper router generates an LSP, it packs all the necessary information-such as the router's area addresses, its neighbors, and its local interface prefixes-into various TLVs and places them into a single PDU. If the amount of information exceeds the Maximum Transmission Unit (MTU) of the interface, the router will generate additional LSPs (fragmented LSPs) to carry the remaining TLVs.
Options A and B are incorrect because restricting an LSP to a single TLV would make the protocol incredibly inefficient, and the very nature of IS-IS is its ability to support multiple network layer protocols (not just IPv4) through its agnostic TLV-based transport.


질문 # 56
Click the Exhibit button.

Referring to the exhibit, which two statements are true? (Choose two.)

정답：A,D

설명：
The routing table shows two equal-cost next hops for the prefix and both are installed in the forwarding table, which means the router is selecting both next hops for forwarding traffic. This indicates equal-cost multipath forwarding.
The forwarding table entry shows a load-balancing group containing both next hops, which reflects the default Junos behavior of performing load balancing across equal-cost paths when multiple next hops exist for the same route.


질문 # 57
......

Juniper인증JN0-364시험을 패스함으로 취업에는 많은 도움이 됩니다. KoreaDumps는Juniper인증JN0-364시험패스로 꿈을 이루어주는 사이트입니다. 우리는Juniper인증JN0-364시험의 문제와 답은 아주 좋은 학습자료로도 충분한 문제집입니다. 여러분이 안전하게 간단하게Juniper인증JN0-364시험을 응시할 수 있는 자료입니다.

JN0-364완벽한 덤프: https://www.koreadumps.com/JN0-364_exam-braindumps.html

Juniper JN0-364 덤프는 고객님의Juniper JN0-364시험패스요망에 제일 가까운 시험대비자료입니다, KoreaDumps JN0-364완벽한 덤프에서는 소프트웨어버전과 PDF버전 두가지버전으로 덤프를 제공해드립니다.PDF버전은 구매사이트에서 무료샘플을 다움받아 체험가능합니다, Juniper JN0-364유효한 공부문제 아마 많은 유사한 사이트들도 많습니다, JN0-364최신버전 공부자료에 있는 문제를 잘 이해하고 완벽하게 공부하시면 많은 지식을 장악할뿐만아니라 가장 편하게 JN0-364 시험에 대비할수 있습니다, 하지만 모두 다 알고계시는그대로Juniper인증JN0-364시험은 간단하게 패스할 수 있는 시험이 아닙니다.

태범의 말에 주아가 뒤늦게 고개를 끄덕였다, 리사는 살짝 인상을 쓰고 다문 입술을 손가락 끝으로 매만지고 있었다, Juniper JN0-364 덤프는 고객님의Juniper JN0-364시험패스요망에 제일 가까운 시험대비자료입니다.

인기자격증 JN0-364유효한 공부문제 시험 덤프자료

KoreaDumps에서는 소프트웨어버전과 PDF버전 두가지버JN0-364전으로 덤프를 제공해드립니다.PDF버전은 구매사이트에서 무료샘플을 다움받아 체험가능합니다, 아마 많은 유사한 사이트들도많습니다, JN0-364최신버전 공부자료에 있는 문제를 잘 이해하고 완벽하게 공부하시면 많은 지식을 장악할뿐만아니라 가장 편하게 JN0-364 시험에 대비할수 있습니다.

하지만 모두 다 알고계시는그대로Juniper인증JN0-364시험은 간단하게 패스할 수 있는 시험이 아닙니다.

그리고 KoreaDumps JN0-364 시험 문제집의 전체 버전을 클라우드 저장소에서 다운로드할 수 있습니다: https://drive.google.com/open?id=19OW6SSL5VpUGzYj3VcPwsF9jf-lzAYJB

Report this wiki page